Product ID:ABLEFILM 559 MGO
MSDS Date:01/13/1988
FSC:8040
NIIN:01-183-0952
MSDS Number: BLLFM

Emergency Phone: 800-424-9300 CHEMTREC

Info Phone: 213-764-4600

Cage: 9V874

Telephone: 310-764-4600

Cage: 21109

POLYOXYPROPYLENE DIAMINE (POPDA) (CORROSIVE LIQUID)

CAS: 9046-10-0

LD50 LC50 Mixture:DERMAL LD50 (RBT) 0.670 G/KG FOR POPDA;*
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALED: MAY CAUSE IRRITATION OF UPPER
RESPIRATORY TRACT. CONTACT WITH SKIN: CAN CAUSE SKIN IRRITATION AND
DERMATITIS. CONTACT WITH EYES: MAY CAUSE IRRITATION. ABSORBED
THROUGH SKIN: NOT LIKELY TO BE ABSORBED IN TOXIC AMOUNTS.
Explanation of Carcinogenicity:*ORAL LD50 (RATS) 0.58 G/KG FOR POPDA.

First Aid:EYE CONTACT: FLUSH WITH WATER FOR AT LEAST 15 MINUTES. SEEK
MEDICAL ATTENTION. SKIN CONTACT: WASH IMMEDIATELY WITH SOAP AND
WATER. IF IRRITATION PERSISTS, SEEK MEDICAL ATTENTION IMMEDIATELY.
INHALED: REMOVE TO FRESH AIR IMMEDIATELY. INGESTION: SEEK MEDICAL
ATTENTION IMMEDIATELY AND SHOW INSERT CARD.

Flash Point Method:PMCC
Flash Point:>395F,>202C
Extinguishing Media:CARBON DIOXIDE, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS.

Spill Release Procedures:SWEEP UP AND COLLECT IN AN APPROPRIATE
CONTAINER FOR DISPOSAL.

Handling and Storage Precautions:STORE FROZEN AT ALL TIMES.
Other Precautions:AVOID CONTACT WITH SKIN, EYES AND CLOTHING. AVOID
INHALATION OF VAPORS.

Respiratory Protection:USE NIOSH APPROVED ORGANIC VAPOR RESPIRATOR IF
NEEDED.
Protective Gloves:RUBBER
Eye Protection:SAFETY GOGGLES WITH SIDE SHIELDS
Other Protective Equipment:PROTECTIVE EQUIPMENT TO COVER EXPOSED AREAS
Work Hygienic Practices:VENT CURING OVEN TO OUTDOORS. GOOD HOUSEKEEPING
IS REQUIRED.
Supplemental Safety and Health
PRODUCT SHOULD BE USED WITH CAUTION UPON CURING.

Vapor Pres:25 C MM HG
Spec Gravity:2.3
Solubility in Water:INSOLUBLE
Appearance and Odor:WHITE DRY FILM; ODORLESS
Percent Volatiles by Volume:<2.5

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS AND STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:HEAT PRIOR TO CURE.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE AND
AMMONIA.
Conditions to Avoid Polymerization:EXCESSIVE HEAT. IF NOT USED FOR THIN
BOND LINE APPLIC, VIOLENT CHEM REACTION CAN RESULT. VENT CURING
OVEN TO OUTDOORS.

Waste Disposal Methods:DISPOSE IN APPROVED CHEMICAL DISPOSAL AREA OR IN
A MANNER WHICH COMPLIES WITH ALL LOCAL, STATE AND FEDERAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.